新手買餅仔攪問題～懇請前輩指點～

各位前打前輩，小弟想學前打，但仲未買餅仔攪，想問各位前輩，
其實富士輪 和 千又驅x200除了外觀和價錢之外，性能上有甚麼分別？
另外，請問有香港邊度有得買富士輪 和 千又驅x200 ？ and 價錢約几多？
唔該晒～thanks~!


[ 本帖最後由 Mr.Desperado 於 2007-7-16 22:15 編輯 ]

千又驅x200  - Mong Kwok 海"机"社  around $350 la...

Hmm and I am not sure where to buy Fuji Wheel in HK now as it seems like they are out of stock everywhere (I bought my Fuji Wheel at fishing fever for around $100, for your info)

Comparing the two,

Fuji wheel: cheaper, good for DIY

X200: a bit smaller than Fuji wheel (weight I guess about the same), has a line blocker at 6 o'clock position of the wheel which is practical (your line won't get loose that easily comparing to wheels without the block)

It turns more smoothly than Fuji wheel too
               
Hope this helps...

I am not expert...

[ 本帖最後由 stevenl_604 於 2007-7-16 23:04 編輯 ]

浪子師兄..其實你唔止得以上兩個選擇啫..
再諗吓其他呀...
冇錯..富士輪有 diy 空間..
但如果 budget 許可$600~$700 有好 d 嘅選擇
唔好急,,慢慢尼....

當然係買富士輪玩一排先,覺得前打適合你玩先再投資落去.

多謝几位前輩的回覆～多謝～﹗

原帖由 stevenl_604 於 2007-7-16 22:49 發表
千又驅x200  - Mong Kwok 海"机"社  around $350 la...


Hmm and I am not sure where to buy Fuji Wheel in HK now as it seemslike they are out of stock everywhere (I bought my Fuji Wheel atfishing ...

唉.......沒錯，富士輪真的找了很多間也找不到，多謝您的分析﹗

原帖由 kentwby 於 2007-7-17 04:20 發表
浪子師兄..其實你唔止得以上兩個選擇啫..
再諗吓其他呀...
冇錯..富士輪有 diy 空間..
但如果 budget 許可$600~$700 有好 d 嘅選擇
唔好急,,慢慢尼....

係，我都明白$600~$700 有好 d 選擇，但奈何我只是新手兼學生一名，暫時唔想投放太多，其實我買攪的budget只有$300左右......

原帖由 kido 於 2007-7-17 09:50 發表
當然係買富士輪玩一排先,覺得前打適合你玩先再投資落去.

請問前輩知不知道香港邊度有賣～？

[ 本帖最後由 Mr.Desperado 於 2007-7-17 11:07 編輯 ]

Alert on 2nd hand reel!!!  

原帖由 DriftsinkAngler 於 2007-7-17 11:19 發表

                               
登錄/註冊後可看大圖

Alert on 2nd hand reel!!!  

多謝提醒